Student

PE7_2 Electrical engineering: power components and/or systems

ERC 3rd level Code

PE7_12 Electrical energy production, distribution, application

Research Activities

The Educational Laboratory on Electric Power System is dedicated to activities on technological and operational development of electric power systems, networks and installations. The research includes electric power systems at different scales (from user installations and microgrids, up to distribution grid and transmission networks) for the evaluation of different kinds of grid analysis (in steady-state operation, in fault conditions, in dynamic behaviour) for the development of operation and control methods at different time scales (e.g. long-medium term evolution planning, operation programming, real-time management). Various exchanges with other laboratories and technological demosntrators are in force, to remotely elaborate operation and control strategies and to perform continuous operation analysis of real and experimental installations. The laboratory is exploited as a support to education and didactic activities of the Electric Power Systems group, thanks to the presence of computers, experimental facilities and instrumentation, involving different degree courses of DEI and other Departments, as well as for training and thesis and for third mission.

Department

matteo.ascatigno@poliba.it

Contact Person

Maria Dicorato

maria.dicorato@poliba.it

Technical Staff

Matteo Ascatigno

Companies and Institutions

ENSIEL

Terna S.p.A.

Sorgenia S.p.A.

ENEL X

RFI S.p.A.

Apulia Region

JRC institute for Energy and Transport

IEA DHC

University of Loughborough

Cardiff University

RTWH Aachen

Università di Bologna

MANENS S.r.l.

Projects

Project HORIZON-KDT-JU_2023-1-IA-Focus-Topic-4 “Electronic Components and Systems for flexible, coordinated and resilient Distributed Renewable Energy Systems (ECS4DRES)” – id 101139790, 2024-2027

Project PNRR PE “NEST – Network 4 Energy Sustainable Transition”, Spoke 2 “Energy Harvesting and Off-Shore Renewables”, 2022-2025

Project PNRR CN “Sustainable Mobility Center – MOST”, Spoke 14 “Hydrogen and New Fuels”, 2022-2025

Project “New Future for Duty Vehicles – Hybridate” in a Closed Call for PoC in PNRR CN “Sustainable Mobility Center – MOST”, Spoke 13 “Electric traction systems and batteries”, 2025

Project PRIN 2022 PNRR Project “SMART – Sea wave energy converters and marine tidal turbines”, 2023-2025

Contract with EnSiEL consortium “Analysis of potential impact on National Transmission Network of electric vehicle charging infrastructures” based on Terna-EnSiEL contract ST238, 2023-2025

Contract with Sorgenia S.p.A. “Systematization and widening for procedures for grid studies of electric power system”, 2023-2025

Funding

ECS4DRES – 399 k€

PNRR NEST Spoke 2 – 150 k€

PNRR MOST Spoke 13 PoC Hybridate – 10 k€

PRIN 2022 PNRR - SMART – 10 k€

Terna-EnSiEL contract ST238 – 39 k€

Sorgenia S.p.A. contract – 55 k€

Facilities

Computers for power system simulation

DC microgrid testbed (remotely connected) and energy management system

Educational panels for power installations and safety

Softwares

DigSilent PowerFactory

Matlab-Simulink

Python

Services

Energy management strategies of microgrids in the framework of energy communities and for the provision of network services

Network connection requirements for renewable production plants

Techno-economic power system operation and planning in combination with energy and service markets

Impact of electric vehicle smart charging and vehicle-to-grid on transmission and distribution networks

Optimization problems applied to power system evolution and operation

Innovative technologies for offshore power production

Sizing and operation of energy storage devices for supporting the grid with renewables

Power system operation and control modeling and simulation in static and dynamic conditions

StakeHolder

Address / How to reach us

Via Giovanni Amendola, 132 - POLILAB

Hours

Mon-Fri 8.30-18.30

Area (mq)

120

T4B

filippo.attivissimo — Wed, 22 Dec 2021 12:57:28 +0000

T4B filippo.attivissimo Wed, 12/22/2021 - 13:57

Lab full name

Tech4Biomed

ERC 2nd Level Code

PE7_3 Simulation engineering and modelling

ERC 3rd level Code

PE7_7 Signal processing

PE8_13 Industrial bioengineering

PE8_4 Computational engineering

Research Activities

•   Smart instruments for measurements on components and systems
•   Development of measuring system for health monitoring and wearable sensors
•   Analysis of biomedical signal
•   Medical image processing
•   Environmental monitoring and remote sensing

Department

filippo.attivissimo@poliba.it

Contact Person

Filippo Attivissimo

Companies and Institutions

1. ApuliaBiotech - Bari

2. Item Oxigen srl-Altamura

3. IVIS-Taranto

4. MASMEC Biomed – Modugno (BA)

5. Universitad Politecnica de Valencia

Projects

1. POR Puglia FESR-FSE 2014-2020, bando INNONETWORK - Aiuti a sostegno alle Attività di R&S, “SINACH - Sistemi integrati di navigazione per chirurgia mini invasiva”.

Funding

1. Progetto POR “Tech4biomed - Tecnologie per la Biomedicina” (2017-2019). Amount 300 k€

Facilities

Basic measurement instrumentation (mixed-signal oscilloscopes, arbitrary waveform generators, power supplies, ADC boards)

sensors for biomedical signals

patient simulator

multiparametric monitors

Electrical Safety Analyzer

Softwares

Mathworks Matlab

National Instruments LabVIEW

Services

teaching

Internship

prototyping

StakeHolder

Address / How to reach us

Polytechnic University of Bari Via E. Orabona, 4 “Luigi Salvatore” building, 2th floor

Hours

Mon – Fri, 8.00 AM - 7.00 PM

OML

filippo.attivissimo — Wed, 22 Dec 2021 12:00:40 +0000

OML filippo.attivissimo Wed, 12/22/2021 - 13:00

Lab full name

OpenMultiLab

ERC 2nd Level Code

PE7_2 Electrical engineering: power components and/or systems

ERC 3rd level Code

PE7_7 Signal processing

PE7_4 (Micro and nano) systems engineering

PE7_3 Simulation engineering and modelling

PE8_4 Computational engineering

Research Activities

Design and prototyping of PC-, microcontroller- and DSP-based mixed signals Data Acquisition (DAQ) and Data Processing Systems
Industrial circuits, PLC programming and machines diagnostic for faults prevention
Wireless Sensor Networks (WSN) design and prototyping
Energy harvesting and energy monitoring from renewable energy sources
Time Domain Reflectometry measurement system and waveform analysis
Power quality measurements

Department

filippo.attivissimo@poliba.it

Contact Person

Filippo Attivissimo

Companies and Institutions

SITAEL S.p.A. - Mola di Bari

MASMEC S.p.A. - Bari

SIPAL S.p.A. - Torino

Centro Studi Componenti per Veicoli S.p.A.(CVIT) - Gruppo Bosch – Modugno (BA)

MER MEC – Monopoli

Schneider Electric S.p.A. – Modugno (BA)

Projects

Progetto PON R&I 2014-2020, “RAFAEL - Sistema per la previsione e la gestione del rischio sulle Infrastrutture Critiche nel Sud Italia” Area di specializzazione “Smart Secure & Inclusive Communities”, 2018-2020.

Progetto PON R&I 2014-2020 “FURTHER - FUture Rivoluzionarie Tecnologie per velivoli più Elettrici” Area di specializzazione “Aerospazio, 2018-2020.

Progetto PON R&I 2014-2020 “MITIGO- Sistemi integrati per la mitigazione del rischio idrogeologico e sismico di pendii, strutture e infrastrutture strategiche in contesti geomorfologici tipici dell’Italia Meridionale”, 2018-2020).

Progetto PON R&I 2014-2020 “Maia: Monitoraggio attivo dell’infrastruttura ”, Area di specializzazione “Mobilità sostenibile”, 2018-2020.

Funding

Progetto POR Puglia dal titolo “Openmultilab” per la realizzazione di un nuovo laboratorio multidisciplinare del Politecnico di Bari, amount 250 k€

Facilities

Basic measurement instrumentation (mixed-signal oscilloscopes, arbitrary waveform generators, power supplies, ADC boards)

3D FFF and resin printers

6 DOFs Robotic arm

160 l climatic chamber

PXI-based high frequency modular vector signal generators and digitizers

Softwares

Mathworks Matlab

National Instruments LabVIEW

Services

Teaching

Internship

3Electronic circuits design and prototyping

StakeHolder

Address / How to reach us

Polytechnic University of Bari Via E. Orabona, 4 “Luigi Salvatore” building, underground floor

Hours

Mon – Fri, 8.00 AM - 7.00 PM

MAE Lab

francesco.cupertino — Wed, 22 Dec 2021 11:08:56 +0000

MAE Lab francesco.cupertino Wed, 12/22/2021 - 12:08

Lab full name

Laboratorio di Macchine e Azionamenti Elettrici – Officine Politecniche

ERC 2nd Level Code

PE7_2 Electrical engineering: power components and/or systems

ERC 3rd level Code

PE7_12 Electrical energy production, distribution, application

Research Activities

Progettazione di convertitori di potenza per uso avionico;
Caratterizzazione di dispositivi di potenza;
Progettazione e validazione di algoritmi di controllo per convertitori di potenza multilivello

Department

francesco.cupertino@poliba.it

Contact Person

Francesco Cupertino

Technical Staff

Rinaldo Consoletti

rinaldo.consoletti@poliba.it

Companies and Institutions

GE Avio SRL, Arol SPA; EXPRIVIA SPA;

NUOVO PIGNONE SPA; BOSCH SPA; LEONARDO FINMECCANICA;

ISOTTA FRASCHINI MOTORI SPA; MERMEC GROUP; AUTOMOTIVE MASMEC SPA;

TESMEC SPA; UNISALENTO; INFN; CNR

Projects

Progetto CARETRON – Computerized mAintenance management system for industRial EquipmenT opeRatiONs” (CETMA) - MISE/REGIONE PUGLIA;

Progetto di Ricerca Industriale e Sviluppo Sperimentale, area di specializzazione “Aerospazio”, codice identificativo ARS01_01283, dal titolo “FURTHER - FUture Rivoluzionarie Tecnologie per velivoli più Elettrici”;

POR Puglia FESR-FSE 2014-2020 Asse prioritario 1 – Ricerca, sviluppo tecnologico, innovazione Azione 1.6 “Bando Innonetwork sostegno alle attività di R&S per lo sviluppo di nuove tecnologie sostenibili, di nuovi prodotti e servizi”: “GreenMill 4.0"

Progetto di ricerca PON R&C 2007-2013 - “MEARI: Gestione Ibrida dell’Energia per applicazioni aeronautiche”;

Progetto di Ricerca “PON R&C 2007-2013, Asse I – Titolo II : “AMIDERHA – Sistemi avanzati mini - invasivi di diagnosi e radioterapia”.

Funding

FURTHER: Euro 1.521.567,50;

MEARI: Euro 1.254.443,00;

CARETRON: Euro 1.132.500,00;

GreenMill 4.0: Euro 181.171,20.

Facilities

Schleich motor analyzer (misura di resistenza di precisione, misura di resistenza di isolamento degli avvolgimenti, prove di scarica parziale),

Oscilloscopi digitali Teledyne LeCroy (misure di corrente e tensione),

unità dSPACE (controlli utili alla caratterizzazione),

Torsiometro HBM T20WN (misure di coppia),

alimentatori a corrente continua (MagnaPower) e corrente alternata (Pacific);

Quadri elettrici con inverter customizzati in configurazione back-to-back

motori elettrici accoppiati in configurazione motore/freno dotati di encoder, sistemi dSpace.

Softwares

MagNet, FEMM

MATLAB per elaborazione in post processing;

MATLAB/Simulink per la progettazione degli algoritmi, Control Desk per implementare gli algoritmi su sistemi dSpace;

Ansys Engineering Simulation Software;

PLEXIM Electrical Engineering Software.

StakeHolder

Address / How to reach us

Officine Politecniche (ex Officine Scianatico) via Amendola 132 – BARI Piano Zero.

Hours

09:00 – 18:00

Power Electronics Laboratory (PELS Lab)

vitogiuseppe.monopoli — Wed, 22 Dec 2021 10:49:15 +0000

Power Electronics Laboratory (PELS Lab) vitogiuseppe.m… Wed, 12/22/2021 - 11:49

Lab full name

Power Electronics Laboratory - Laboratorio di Elettronica di Potenza

ERC 2nd Level Code

PE7_2 Electrical engineering: power components and/or systems

ERC 3rd level Code

PE7_12 Electrical energy production, distribution, application

Research Activities

The Power Electronics Laboratory deals with innovative, efficient and reliable systems for the conversion of energy from renewable sources and innovative, efficient and reliable systems for the electrification of different means of transport.

MODULAR CONVERTERS - The high efficiency operation of power electronic converters is essential to enable their large-scale diffusion both in grid applications and in the electrification of means of transport. Modular converters are a family of power electronics converters increasingly used in high voltage and high power applications for their many advantages, such as the use of low voltage semiconductor technology instead of high voltage modules (less efficient and widespread) and modularity, which is directly associated with scalability, redundancy, fault-tolerant operation and ease of maintenance. Within the MMCC family of modular converters, two architectures are of particular interest to the research group due to their remarkable potential, namely the modular multilevel converter (MMC) and the cascaded H-bridge converter (CHB). The research group is working on advanced modulation and control techniques to improve efficiency, stability and reliability of such converters.

HIGH-FREQUENCY CONVERTERS - In the field of high-speed electric drives, the use of inverters with Wide-Bandgap Devices (SiC MOSFET and GaN HEMT) represents a solution that allows an improvement of the converter efficiency. The introduction of high switching frequency devices with SiC MOSFET or GaN HEMT technology leads to the emergence of several issues, especially related to the considerable stresses imposed on the insulation systems by the sudden voltage variations, reducing the reliability of the system. The research group is working on innovative software and hardware solutions to address these issues.

Department

vitogiuseppe.monopoli@poliba.it

Contact Person

Vito Giuseppe Monopoli

Technical Staff

Rinaldo Consoletti

rinaldo.consoletti@poliba.it

Companies and Institutions

- ETH Zürich (Switzerland)

- Christian-Albrechts-Universität zu Kiel (Germany)

- University of Seville (Spain)

- GE Avio S.r.l.

- LEONARDO S.p.A.

- ISOTTA FRASCHINI MOTORI S.p.A.

- ENEL GREEN POWER S.p.A.

- TESMEC S.p.A.

- E1 S.r.l.

Projects

- PON, “FURTHER - FUture Rivoluzionarie Tecnologie per velivoli più Elettrici”, codice identificativo ARS01_01283

- PRIN 2017 - 2017MS9F49_002 – “Advanced power-trains and -systems for full electric aircrafts”

- Partenariati Estesi PNRR NEST "Network 4 Energy Sustainable Transition", Codice Progetto PE00000021

- Centro Nazionale PNRR MOST "Mobilità Sostenibile", Proof of Concept: NEWBGAN

Funding

- PON FURTHER: € 1.521.567,50

- PRIN 2017: € 156.348,00

- PE NEST: € 1.085.657,70

- CN MOST, PoC NEWBGAN: € 205.750

Facilities

- CNC milling machine for PCB printing

- OpalRT real-time simulator for electrical systems

- Spitzenberger & Spies power amplifier (DC, AC 3-phase 15 kVA)

- Climate chamber

- Soldering station

- Digital oscilloscopes, current probes, voltage probes, Rogowski probes

- Stabilized benchtop power supplies

- Benchtop signal generators

- DC power supplies up to 600 V programmable (Magna Power)

- Programmable AC 3-phase power supply (Pacific)

- Power resistive loads

- Digital wattmeters

- AMD/Xilinx Zynq 7000 SoC control systems with Arm Cortex processor and Artix-7 FPGA

- National Instruments SoM-based rapid prototyping control systems programmable in Labview

Softwares

- MATLAB/Simulink

- PLEXIM Electrical Engineering Software PLECS

- National Instruments Multisim

- Ansys Engineering Simulation Software

- AMD Vivado

- AMD Vitis

- National Instruments LabView

StakeHolder

Address / How to reach us

- Officine Politecniche (ex Officine Scianatico), via Amendola 132, 70126 Bari

- Dipartimento di Ingegneria Elettrica e dell’Informazione, via Edoardo Orabona 4, 70125 Bari

AE&M Lab

cristoforo.marzocca — Thu, 16 Dec 2021 10:00:55 +0000

AE&M Lab cristoforo.marzocca Thu, 12/16/2021 - 11:00

Lab full name

Applied Electronics and Microelectronics

ERC 2nd Level Code

PE7_3 Simulation engineering and modelling

ERC 3rd level Code

PE7_4 (Micro and nano) systems engineering

PE7_11 Components and systems for applications

Research Activities

The lab has long been involved in the development and characterization of multichannel integrated circuits for read-out of solid-state detectors and sensors for high energy physics and medical imaging. Another related activity is the characterization of detectors, sensors and electronic devices. In more detail, the main current research lines are the following:

Design of multichannel mixed-signal integrated circuits (ASIC) for the read-out of solid-state detectors used in high energy physics experiments and medical imaging applications

Development of sensor interface electronics for environmental monitoring
Prototyping (via access to the European consortium EUROPRACTICE) and characterization of integrated circuits
Design and realization of hardware/firmware systems based on programmable devices (FPGA)
Characterization of solid-state detectors for physics experiments and medical imaging applications (Silicon Photomultipliers)

Department

cristoforo.marzocca@poliba.it

Contact Person

Cristoforo Marzocca

Technical Staff

Vincenzo Scarola, Gennaro Gelao

vincenzo.scarola@poliba.it

Companies and Institutions

SLAC Stanford, Menlo Park (CA, USA)

CERN, Geneva (Switzerland)

Munster Technological University, Cork (Ireland)

Istituto Nazionale di Fisica Nucleare

Fbk-IRST, Trento

AVIO AERO, Bari

ETG Risorse, Chivasso (To)

ITEL, Ruvo di Puglia

Matrix s.r.l., Conversano (Ba)

Cupersafety s.r.l., Conversano (Ba)

Microlaben s.r.l.(spin-off company of Politecnico di Bari)

Projects

CMS experiment (CERN – Geneva)

H2020 “PASSEPARTOUT” (European Community)

H2020 "EVOQUE" (European Community)

POC "SPHERE" PNRR

Research contract “Collaboration on the development of a Time-of-Flight (ToF) readout system for Silicon Photon Multipliers” (SLAC Stanford)

Innolabs “Sistema partecipativo attivo per la sensibilizzazione delle comunità al rischio di esposizione al GAS RADON” (Apulia Regional government)

PON “FURTHER - FUture Rivoluzionarie Tecnologie per velivoli più Elettrici” (MIUR)

Funding

MIUR – 445 k€

SLAC Stanford – 34 k€

Apulia Regional government – 20 k€

European Community – 120 k€

Politecnico di Bari – 6 k€

Facilities

-Linux workstations for IC design, equipped with the suite Cadence IC

-Semi-automatic probestation Karl Suss PM8, optical microscope 50X Karl Suss

-Logic state analyzer Tektronix, 32 channels

-Semiconductor parameter analyzers HP4145B and 4155B

-Spectrum analyzer Agilent N1996A, 100kHz-6GHz

-Oscilloscope DPO Tektronix 4GHz, 4 channels

-Oscilloscope Rohde-Schwarz 4GHz, 4 channels

-Arbitrary signal generator Tektronix, 200MHz

-Standard lab instrumentation (stabilized power supplies, digital multimeters, low-end oscilloscopes and function generators)

Softwares

Suite Cadence IC for electronic design

Services

IC design and prototyping, via EUROPRACTICE service (only for research and educational purposes, no commercial activities)

StakeHolder

Address / How to reach us

Via Orabona 4, 70125 – Bari (Italy)

Dipartimento di Ingegneria Elettrica e dell’Informazione

Plesso Salvatore, IV floor

DEI main building, II floor

Hours

Mon - Fri 9:00 - 17:30

Area (mq)

MAULab

cesare.verdoscia — Thu, 09 Dec 2021 12:28:31 +0000

MAULab cesare.verdoscia Thu, 12/09/2021 - 13:28

Lab full name

Architectural and Urban Modeling Laboratory

ERC 2nd Level Code

PE8_3 Civil engineering, architecture, maritime/hydraulic engineering, geotechnics, waste treatment

ERC 3rd level Code

Research Activities

The Architectural and Urban Modelling Laboratory (MAULab) of DICATECh, promotes and coordinates scientific research in the field of Survey and Representation of Architecture, Monuments, Natural and Urbanised Environment, with digital techniques, offering itself as an institutionally operating subject in the field of scientific research and studies in the specific field of digital 3D Modelling of buildings for Virtual, Augmented and Mixed Reality (VR/AR/MR) even within BIM and HBIM processes.

Department

DICATECH

Contact Person

Cesare Verdoscia

cesare.verdoscia@poliba.it

Technical Staff

Riccardo Tavolare

riccardo.tavolare@poliba.it

Companies and Institutions

Asset-Apulia Region;

Arca Capitanata - Regional Agency for housing and living;

Municipality of Ruvo di Puglia (BA);

Municipality of Cisternino (BR);

Municipality of Trinitapoli (BAT);

Graitec s.r.l.;

ICMQ s.p.a.

Geomax (3D measuring systems)

Projects

Specialist technical consultancy concerning the preparation of studies and analyses aimed at drafting amendments to the municipal regulations for the occupation of public land. (Municipality of Ruvo di Puglia)

Research projects called POLIBIM POLIMAP. (Heritage Office of the Polytechnic of Bari)

Innovative techniques for the survey and architectural representation applied to the knowledge process of a historical building: Starita Palace in Bari.

Design and delivery of training courses aimed at the understanding of design, analysis and verification methodologies in BIM environment.

Facilities

LaserScanner FARO 3D 120

Geomax Zoom 3D

3D Eye 2.0

DJI Spark drone

Manfrotto 360 VR

VR Oculus Rift

CGraphics Workstation

Softwares

MAXON Cinema 4D

Autodesk Revit

Autodesk Navisworks

Autodesk Infraworks

Autodesk Recap PRO

Autodesk Autocad

Unreal Engine

Agisoft Metashape

CloudCompare

MeshLAB

MATLAB

VisualStudio Code

StakeHolder

Address / How to reach us

Campus Universitario E. Quagliarella, via Orabona, 4 70125 Bari. Building B01, 1st floor.

Hours

Mondays to Fridays from 9 a.m. to 1 p.m.

Link to external content

MAULAB web site

CNC Lab

luigimaria.galantucci — Thu, 07 Oct 2021 15:22:59 +0000

CNC Lab luigimaria.gal… Thu, 10/07/2021 - 17:22

Lab full name

Computer numerical control machines laboratory

ERC 2nd Level Code

Research Activities

The Computer numerical control machines laboratory was founded in 1999. It is part of the scientific area of Manufacturing Systems and Technologies ING-IND/16.

The laboratory presents several CNC machines as well as a hydraulic press for moulding of thermoplastic materials.

The laboratory equipment has been adopted for research activities supporting the more innovative technologies, through the realization of prototypes and tools. Specimens for calibration procedure of measuring instruments, samples for material characterization and specifically designed tooling systems have been realized on CNC Machines. Moreover, different polymeric materials have been tested through the hydraulic press with different moulds.

Department

luigimaria.galantucci@poliba.it

Contact Person

Luigi Maria Galantucci

Companies and Institutions

Università di Bologna – Policlinico S. Orsola-Malpighi

Università Cattolica del Sacro Cuore Roma

Università di Bari - Medicina legale

Università di Napoli Federico II

Dipartimento Interateneo di Fisica “Michelangelo Merlin”

CNR Istituto di Fotonica e Nanotecnologie

Università di Kragujevac – Faculty of Engineering (Serbia)

Leone Spa

ICAM srl

Bosch TDI

GE Avio srl

Roboze srl

GE Oil and Gas

COFRA

Pezzol

Base Protection

Simitecno srl

Adler Ortho srl

Facilities

Alfa Engineering MM 430, CNC Machine Centre, for vertical milling and reaming, 4 controlled axis, Numerical Control SIEMENS 802D sl, ISO Spindle 40 power 7 kW, max speed 10000 g/min, automatic tool change, working volume 900x460x390 mm3

PENTAMAC srl QUICLY’T 1000, CNC Lathe. Distance between centres 1000 mm, max turning diameter 460 mm. Max spindle speed 2000 RPM. Electrical turret with 6 positions

FCN 500, CNC 4 axis milling machine, ISO spindle 30 -pot. 1 kW, vel. 100-3000 g/min, with Ethernet Motion Controller 7761M, working volume 500x140x215 mm3

DEMAG-ERGOTECH, Hydraulic press (maximum load: 80 ton) equipped for moulding of thermoplastic materials

Services

Creation of prototypes and small batches for different application sectors of Mechatronics

StakeHolder

Address / How to reach us

Viale Japigia 182 - Bari –Italy (DMMM)

Microtronic Lab

luigimaria.galantucci — Thu, 07 Oct 2021 15:15:15 +0000

Microtronic Lab luigimaria.gal… Thu, 10/07/2021 - 17:15

Lab full name

Microtronic Laboratory

ERC 2nd Level Code

Research Activities

The Microtronic laboratory, operating in the scientific area of Manufacturing systems and technologies (ING-IND/16), is part of the Microtronic network of laboratories. It is aimed to mechatronic sectors which are characterized by an ever higher request for micro-components realized in a large variety of materials.

The research activities are focused on the combination of micro-milling and additive manufacturing technologies for the realization of 3D complex parts at micro-scale level. Microscope and profilometer for surface analysis are used for performance verification of the micro-machining processes.

The machines and measuring instruments present in the laboratory are well suited for feasibility studies and services aimed at local companies comprised in the mechatronic district and operating in the fields of precision mechanic, tool design and automotive and machine components.

Department

luigimaria.galantucci@poliba.it

Contact Person

Luigi Maria Galantucci

Companies and Institutions

Leone Spa

Bosch TDI

ICAM srl

Roboze srl

GE Avio srl

GE Oil and Gas

Adler Ortho srl

Simitecno srl

Facilities

KUGLER Microgantry micro, 5 axis micro-milling machine, 1kW power spindle and 60000 RPM of maximum velocity, positioning accuracy comprised between 0,5 e 1,0 micrometers for Cartesian axis and ±1 arcsec for rotary axis

Hirox RH-2000 microscope, able to ensure several magnification levels (up to 10000x) wit rotary head and tilting table

Taylor Hobson CCI-MP HS, optical profilometer based on interferometric principle equipped for a minimum x-y resolution equal to1µm

WASP DELTA 4070, 3D printer for Poly(lactic acid) polymeric material. The maximum printing volume is 400x400x700 mm3

Zortax M-200, 3D printer optimized for ABS material and printing volume equal to 200x200x150 mm3

M-One MAKEX, additive manufacturing machine based on liquid resins photo polymerization and characterized by a xy resolution ranging from 60 to 75µm

Services

Feasibility studies and service activities for micro-processing and characterization of small series of mechatronic components

StakeHolder

Address / How to reach us

Viale Japigia 182- Bari- Italy (DMMM)

RaP-RE Lab

luigimaria.galantucci — Thu, 07 Oct 2021 14:59:05 +0000

RaP-RE Lab luigimaria.gal… Thu, 10/07/2021 - 16:59

Lab full name

Laboratory for Rapid Prototyping and Reverse Engineering

ERC 2nd Level Code

Research Activities

The research activities are oriented to the analysis and the study of new methodologies for AM and RE implementation. In AM field, new chemical treatments for surface finishing have been developed. Moreover, process parameters have been optimized in order to improve mechanical properties, reduce production time and surface roughness.

In RE, new 3D scanning methodologies have been developed based on photogrammetry, for different applications, from mechatronic to biomedical and forensic field. Calibration procedures have been improved for several optical configurations even at micro-scale level.

The laboratory was firstly funded by Piano Triennale MURST (D.M. 21/6/99). Thanks to some industrial research projects of “Distretto Tecnologico delle Meccatronica Pugliese, Regione Puglia, CIPE 20/04, intervento cod. DM01” and POR it has been constantly updated.

Department

luigimaria.galantucci@poliba.it

Contact Person

Luigi Maria Galantucci

Companies and Institutions

Università Cattolica del Sacro Cuore Roma

Università di Napoli Federico II

Università di Bologna – Policlinico S. Orsola-Malpighi

Università di Bari - Medicina legale

Università di Kragujevac – Faculty of Engineering (Serbia)

Dipartimento Interateneo di Fisica “Michelangelo Merlin”

CNR Istituto di Fotonica e Nanotecnologie

Leone Spa

Bosch TDI

ICAM srl

GE Avio srl

Roboze srl

GE Oil and Gas

Simitecno srl

Adler Ortho srl

COFRA, Pezzol

Base Protection

Saint-Gobain

UTG Lavorazioni

Facilities

Stratasys FDM 3000 using ABS material with layer height equal to 0.1 mm. Maximum working volume 254x254x406 mm3

WASP DELTA 4070, 3D printer for Poly(lactic acid) polymeric material. The maximum printing volume is 400x400x700 mm3

Zortax M-200, 3D printer optimized for ABS material and printing volume equal to 200x200x150 mm3

M-One MAKEX, additive manufacturing machine based on liquid resins photopolymerization and characterized by a xy resolution ranging from 60 to 75µm

Konica Minolta Vivid 910i, 3D automatic Laser Scanner: working volume ranging from 111*83*40 mm3 to 1196*897*750 mm3, accuracy X: ±0.22mm, Y: ±0.16mm, Z: ±0.10mm, scanning time comprised between 0.3 and 2.5 sec

Roland PIX 250, desktop 3D rotary laser scanner

CMM – Coordinate Measuring machine DeMeet 400, equipped with both contact and optical sensors. Measuring volume 400x250x200 mm3, resolution of 0.5 µm

Measuring arm GARDA, with Renishaw probe, spherical working volume of 2.5 m of diameter, accuracy of 0.05 mm

Line Laser Scanner Kreon, 16000 points per second of scanning speed, accuracy of 0.05 mm

Micro Z-Scan, Photogrammetric 3D scanning instrument

Optimet QC Scanner type 1 ROHS, holographic 3D scanner

Optimet ConoScan 3000, compact and non-contact conoscopic holography 3D measuring instrument, for 120x120 mm2 sized parts

ConoProbe HD (High Definition) - Mark 3.0, sensor for high precision 3D measurements (micrometric resolution) based on conoscopic holography principle

Optimet NanoConoprobe, conoscopic holography sensor for transparent and reflective surfaces and thickness evaluation comprised between 1-10 µm

Microplan, 5 axis conoscopic holography scanning system for axial-symmetrical 2D and 3D profiles

Services

Realization of prototypes and small batches of parts for different application sectors of Mechatronics and medicine, including forensics, in the textile, footwear, orthodontic field, in the field of plastic and maxillofacial surgery

StakeHolder